Projet

Général

Profil

EdgeOS » Historique » Version 29

Version 28 (Christian Frabel, 04/01/2023 17:07) → Version 29/31 (Christian Frabel, 04/01/2023 17:08)

{{>toc}}

h1. EdgeOS

ES-48-Lite EdgeOS 1.7.3

h2. Documentation

https://dl.ubnt.com/guides/edgemax/EdgeOS_UG.pdf
https://dl.ubnt.com/guides/edgemax/EdgeSwitch_CLI_Command_Reference_UG.pdf

h2. Commandes

<pre>
(UBNT EdgeSwitch) #show mac-addr-table

VLAN ID MAC Address Interface IfIndex Status
------- ------------------ --------------------- ------- ------------
1 00:01:E8:8B:4F:CF 0/49 49 Learned
1 00:08:7C:3C:29:03 0/49 49 Learned
128 9C:B6:54:06:7E:56 0/5 5 Learned
...
</pre>

<pre>
show interfaces status all
Port Name State Mode Status Type Status
--------- ---------------------------- ------ ---------- ---------- ------------------ ------------
0/1 Down Auto Unknown Inactive
0/2 Down Auto Unknown Inactive
0/3 Up Auto 100 Full Unknown Active
...

(UBNT EdgeSwitch) #show interfaces switchport

Port: 0/1
VLAN Membership Mode: General
Access Mode VLAN: 1 (default)
General Mode PVID: 3131
General Mode Ingress Filtering: Disabled
General Mode Acceptable Frame Type: Admit all
General Mode Dynamically Added VLANs:
General Mode Untagged VLANs: 3131
General Mode Tagged VLANs: 3199
General Mode Forbidden VLANs: 1,20,128,376,3132,3166,3175
Trunking Mode Native VLAN: 1 (default)
Trunking Mode Native VLAN tagging: Disable
Trunking Mode VLANs Enabled: All
Protected Port: False

Port: 0/2
...
</pre>

<pre>
(UBNT EdgeSwitch) #show fiber-ports optics-info all

Link Link Nominal
Length Length Bit
50um 62.5um Rate
Port Vendor Name [m] [m] Serial Number Part Number [Mbps] Rev Compliance
-------- ---------------- --- ---- ---------------- ---------------- ----- ---- ----------------
0/49 OEM 0 0 SG35E40803862 SFP+10GSMD3120LC 10300 A 10GBase-LR
0/50 OPTIC 0 0 STC03051500015 OPTICSFP+10GCP3M 10300 A0 DAC

(UBNT EdgeSwitch) #show fiber-ports optics all

Output Input
Port Temp Voltage Current Power Power TX LOS
[C] [Volt] [mA] [dBm] [dBm] Fault
-------- ---- ------- ------- ------- ------- ----- ---
0/49 45.2 3.332 31.5 -3.079 -3.223 No No
0/50 N/A N/A N/A N/A N/A N/A N/A

Temp - Internally measured transceiver temperatures.
Voltage - Internally measured supply voltage.
Current - Measured TX bias current.
Output Power - Measured optical output power relative to 1mW.
Input Power - Measured optical power received relative to 1mW.
TX Fault - Transmitter fault.
LOS - Loss of signal.
</pre>

h3. Allumer un port et remplir sa description

<pre>
(UBNT EdgeSwitch) #conf
(UBNT EdgeSwitch) (Config)#interface 0/33

(UBNT EdgeSwitch) (Interface 0/33)#no shutdown

(UBNT EdgeSwitch) (Interface 0/33)#description gentilserveur

(UBNT EdgeSwitch) (Interface 0/33)#exit

(UBNT EdgeSwitch) #write memory
This operation may take a few minutes.
Management interfaces will not be available during this time.
Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

</pre>

<pre>
(UBNT EdgeSwitch) #write memory

This operation may take a few minutes.
Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!
</pre>

<pre>
(UBNT EdgeSwitch) #conf

(UBNT EdgeSwitch) (Config)#interface 0/35

(UBNT EdgeSwitch) (Interface 0/35)#shut

(UBNT EdgeSwitch) (Interface 0/35)#do write memory

This operation may take a few minutes.
Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

(UBNT EdgeSwitch) (Interface 0/35)#

</pre>

<pre>
(UBNT EdgeSwitch) (Config)#interface 0/12-0/15

(UBNT EdgeSwitch) (Interface 0/12-0/15)#shut
</pre>

<pre>
(s58) #copy nvram:startup-config tftp://192.168.3.19/s58

Mode........................................... TFTP
Set Server IP.................................. 192.168.3.19
Path........................................... ./
Filename....................................... s58
Data Type...................................... Text Configuration

Management access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y

File transfer operation completed successfully.

(s58) #

</pre>

h2. Exemple

À titre d'exemple, activons le port 1 du switch s54 localisé à Picto afin d'y connecter un dispositif.
On peut se connecter au switch de diverses façons, cependant à distance, on peut se connecter d'abord sur nagios.tetaneutral.net et, de là, atteindre s54.
Ceci nécessite d'avoir sa clef sur nagios afin de permettre la connexion ssh.

*@ssh @*ssh -lroot -p2222 nagios.tetaneutral.net@* nagios.tetaneutral.net*@
Connexion à s54 passwd: ubnt
ssh ubnt@s54
Après connexion au switch, on passe en root pw: ubnt
enable
On passe ensuite en mode config
conf
Pour la config du port 1
interface 0/1
On active le port
no shut
On revient en mode config général
exit
Puis on sort du mode config
exit
Il faut encore sauver la config dans une mémoire permanente
write mem
La configuration est terminée