Mikrotik¶

RouterOS

http://wiki.mikrotik.com/wiki/MikroTik_RouterOS
http://wiki.mikrotik.com/wiki/Manual:TOC
http://wiki.mikrotik.com/wiki/Manual:Webfig

http://www.mikrotik.com/download.html
http://wiki.mikrotik.com/wiki/Upgrading_RouterOS

RB750UP¶

http://routerboard.com/RB750UP

Nice box : http://forum.mikrotik.com/viewtopic.php?p=297825#p297825

Voltage : http://forum.mikrotik.com/viewtopic.php?f=3&t=58124

limit on power out port is 500mA regardless of output voltage. so at 12V you will be able to power only MAX 6W device. while at 30V 15W.
If you power RB570UP with PoE 24V adapter over 100m cable, then resulting output voltage at full load (all 4 ports giving out 500mA totaling to 2A) then voltage to powered ports at RB750UP end will be around 21V then losses on cable and protections you end up with around 19V at the end device. and cables stretching for 200m from PSU brick.
PoE in port has no input limitation only output is limited to 500mA and with 4 prots it is 2A

• http://wiki.mikrotik.com/wiki/Manual:Upgrading_RouterOS
• To update firmware (latest RouterOS 5.12):
• Files / upload choose file : routeros-mipsbe-5.12.npk (12MB)
• Attendre la fin de upload
• System / Packages / IPv6 schedule for update
• System / Reboot
• about 90 seconds. Note: PoE will be cut during the reboot

chiwa admin VLAN 3175
192.168.3.20

telnet login admin pass (vide)
web

[admin@rb750up-chiwawa] > interface ethernet print                                                                 
Flags: X - disabled, R - running, S - slave 
 #    NAME                               MTU MAC-ADDRESS       ARP        MASTER-PORT                            SWITCH                           
 0    ether1-gateway                    1500 00:0C:42:E9:BA:8A enabled   
 1 R  ;;; To chiwa's router *** NO POE ***
      ether2-master-local               1500 00:0C:42:E9:BA:8B enabled    none                                   switch1                          
 2 RS ;;; to Vince' NS5M -  To Myrys
      ether3-slave-local                1500 00:0C:42:E9:BA:8C enabled    ether2-master-local                    switch1                          
 3 RS ;;; to NS5M east - To CDRX
      ether4-slave-local                1500 00:0C:42:E9:BA:8D enabled    ether2-master-local                    switch1                          
 4 RS ;;; to beaconing NS5M (port balcon.3)
      ether5-slave-local                1500 00:0C:42:E9:BA:8E enabled    ether2-master-local                    switch1         

http://wiki.mikrotik.com/wiki/PoE-Out

/interface ethernet set ether2 poe-out=on
/interface ethernet set ether2 poe-out=off
/interface ethernet set ether2 poe-out=auto

Note:
<obinou> Le poe-out, il faut le mettre à "on" , et pas à "auto".
<obinou> sans ça, j'ai l'impression que le RB fait un power-cycle si il détecte une perte de link
<obinou> or, quand la NSM5 démarre, entre le bootloader & le firmware ca perd le link
<obinou> conclusion: reboot en boucle.

http://forum.mikrotik.com/viewtopic.php?f=3&t=49976&sid=40ea9661791968a896ab35214dc18f15&start=50
http://forum.mikrotik.com/viewtopic.php?f=3&t=57608

[admin@MikroTik-Ouin] > /interface ethernet print detail            
Flags: X - disabled, R - running, S - slave 
 0 R  name="ether1-gateway" mtu=1500 l2mtu=1600 mac-address=00:0C:42:D3:94:D5 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps 
 1    name="ether2-master-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D6 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 
 2    name="ether3-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D7 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 
 3 R  name="ether4-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D8 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on 
 4 R  name="ether5-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D9 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on 

RB250GS¶

http://wiki.mikrotik.com/wiki/SwOS

• vlan limitation mikrotik rb250gs http://forum.mikrotik.com/viewtopic.php?f=17&t=45721