Mikrotik » Historique » Version 44

« Précédent - Version 44/142 (diff) - Suivant » - Version actuelle
Laurent GUERBY, 15/11/2013 12:16

Contenu
Mikrotik

Mikrotik¶

RouterOS

http://wiki.mikrotik.com/wiki/MikroTik_RouterOS
http://wiki.mikrotik.com/wiki/Manual:TOC
http://wiki.mikrotik.com/wiki/Manual:Webfig

http://www.mikrotik.com/download.html
http://wiki.mikrotik.com/wiki/Upgrading_RouterOS

http://wiki.mikrotik.com/wiki/Supported_Hardware
http://wiki.mikrotik.com/wiki/Manual:Password_reset
http://wiki.mikrotik.com/wiki/Manual:PoE-Out

Boitiers¶

BoÃ®tiers Rexel trÃ¨s chers
http://www.technic-achat.com/coffret-electrique-ip66-imo,fr,4,144T_XX.cfm (144T0010)
http://www.interprojekt.com.pl/gold-alubox-outdoor-waterproof-case-p-472.html
http://www.materielelectrique.com/coffret-polyester-marina-ip66-ik10-7035-300x220x160-p-6579.html

Montage¶

http://shop.varia-store.com/product_info.php?info=p1390_RF-Elements-EasyBracket---EasyBracket-Universal.html

PoE¶

http://www.i4wifi.eu/en/EU-230V-powering/PoE-convertor-48-V-24-V-802-3af-at.html

Password¶

From: Le Net du Kermeur
Utilitaire mtpass, Ã§a se trouve lÃ : http://manio.skyboo.net/mikrotik/
Ca se compile sous g++, donc sur n'importe quel Linux ou *BSD.
TestÃ© sous OpenBSD, il fait le boulot.

RB433L and RB433UAHL¶

NPK¶

http://routing.explode.gr/node/96
https://forum.openwrt.org/viewtopic.php?id=32320&p=3
https://forum.openwrt.org/viewtopic.php?pid=165526#p165526
https://github.com/lqez/npk
Easy install of OpenWrt on MikroTik's devices https://forum.openwrt.org/viewtopic.php?id=39171
http://wp.ayufan.eu/2013/02/the-rb951g-and-openwrt/

Misc¶

TODO
http://i.mt.lv/routerboard/files/rb433L-series-qg_1377089307.pdf

http://forum.mikrotik.com/viewtopic.php?t=65977&p=336057
RF antenna and close miniPCI ?

Power Consuption¶

eth1 = PoE        192.168.88.101/24
eth2 = milieu     192.168.102.1/24
eth3 = oppose PoE 192.168.103.1/24
wlan1 = minipci du bas 172.31.31.43/24

http://dslrouter.sourceforge.net/stuff/mikrotik/mikrotik/AirMax5_and_Mikrotik_Router_Board_Connection_Guide_revised.pdf

netboot 
rb750up http://forum.mikrotik.com/viewtopic.php?f=3&t=57943&start=50

USB RB750UP http://patchwork.openwrt.org/patch/3252/

http://wiki.openwrt.org/toh/mikrotik/rb750
http://blog.poettner.de/2011/05/27/openwrt-trunk-on-mikrotik-routerboard-411750/

http://wiki.mikrotik.com/wiki/Manual:Netinstall
http://routerboard.com/pricelist/download_file.php?file_id=118

http://www.gowifi.co.nz/userguides/perform-a-netinstall.pdf

http://forum.mikrotik.com/viewtopic.php?f=2&t=66093
reset longer than 20 seconds

https://forum.openwrt.org/viewtopic.php?id=41490

RB433L
idle 108 mA 12V 
+1 eth 130mA 173 mA max au boot

RB433L + ethernet branchÃ© RouterOS 5.11
conso identique RouterOS 5.26
RouterOS 6.6 ?
Volt    mA  mW
(*  5.0 259)1295.0
(*  6.0 227)1362.0
(*  7.0 200)1400.0
(*  8.0 180)1440.0
(*  8.5 175)1487.5
(*  9.0 165)1485.0
(*  9.5 160)1520.0
(* 10.0 152)1520.0
(* 11.0 142)1562.0
(* 11.5 138)1587.0
(* 12.0 132)1584.0 152 pendant file upload  firmware (* 12.0 152)1824.0
(* 12.5 129)1612.5
(* 13.0 125)1625.0
(* 14.0 119)1666.0
(* 15.0 112)1680.0
(* 18.0  99)1782.0
(* 21.0  90)1890.0
(* 24.0  83)1992.0
(* 26.0  79)2054.0
(* 27.0  77)2079.0

RB433L sans ethernet
   V    mA  mW
4.0 off
(*  5.0 206)1030.0
(*  6.0 181)1086.0
(*  7.0 162)1134.0
(*  8.0 146)1168.0
(*  9.0 133)1197.0
(* 10.0 124)1240.0
(* 11.0 116)1276.0
(* 12.0 110)1320.0
(* 13.0 104)1352.0
(* 14.0  99)1386.0
(* 15.0  94)1410.0

diff ethernet pas ethernet constant en watt sur la plage de 265 mW a 260 mW

eth+ R52n-M  5180 AP-bridge 17dBm = 50 mW
(* 12.0 165)1980.0
vs (* 12.0 132)1584.0

0 dBm = 1 mW ou 7 dBm
conso inchangee
(* 12.0 163)1956.0
163-166

tout en bridge cote RB433L 7 dBm = 5 mW avec iperf 100M UDP
175-180
(* 12.0 (- 180 163))204.0 mW

serial http://forum.mikrotik.com/viewtopic.php?f=3&t=76194
http://wiki.openwrt.org/toh/mikrotik/rb433

http://wiki.mikrotik.com/wiki/Manual:Password_reset
http://wiki.mikrotik.com/wiki/MikroTik_Password_Recovery

http://wireless.kernel.org/en/users/Drivers/ath9k/devices
WLM200NX dual band
http://wireless.kernel.org/en/users/Drivers/ath5k

R52n-M
R52Hn

http://download2.mikrotik.com/routeros/5.26/routeros-mipsbe-5.26.npk
http://download2.mikrotik.com/routeros/6.6/routeros-mipsbe-6.6.npk

http://wiki.mikrotik.com/wiki/Netinstall

RB750UP¶

http://routerboard.com/RB750UP

http://blog.lekermeur.net/wp-content/uploads/2012/03/Printemps2012_RB750.pdf

Attention : problÃ¨mes lors que le RB750UP est alimentÃ© en PoE : http://forum.mikrotik.com/viewtopic.php?f=3&t=57943

we are working on new FW that would add useful features that are currently missing. One of them is reworked power management.

Voltage : http://forum.mikrotik.com/viewtopic.php?f=3&t=58124

limit on power out port is 500mA regardless of output voltage. so at 12V you will be able to power only MAX 6W device. while at 30V 15W.
If you power RB570UP with PoE 24V adapter over 100m cable, then resulting output voltage at full load (all 4 ports giving out 500mA totaling to 2A) then voltage to powered ports at RB750UP end will be around 21V then losses on cable and protections you end up with around 19V at the end device. and cables stretching for 200m from PSU brick.
PoE in port has no input limitation only output is limited to 500mA and with 4 prots it is 2A

Upgrade to 5.20


[admin@MikroTik] /interface ethernet poe settings> upgrade
Do you really want to upgrade PoE firmware? [y/n] 
y
Please reboot to finish PoE firmware upgrade.

[admin@MikroTik] /interface ethernet poe settings> pr
                   version: 2.0
  ether1-poe-in-long-cable: no

[admin@MikroTik] /interface ethernet poe> monitor [find]
               name: ether2-master-local ether3-slave-local ether4-slave-local ether5-slave-local
    poe-out-voltage:                                                           23.5V
    poe-out-current:                                                           160mA
      poe-out-power:                                                           3.7W

http://wiki.mikrotik.com/wiki/Manual:Upgrading_RouterOS
To update firmware (latest RouterOS 5.12):
Files / upload choose file : routeros-mipsbe-5.12.npk (12MB)
Attendre la fin de upload
System / Packages / IPv6 schedule for update
System / Reboot
about 90 seconds. Note: PoE will be cut during the reboot

chiwa admin VLAN 3175
192.168.3.20

telnet login admin pass (vide)
web

[admin@rb750up-chiwawa] > interface ethernet print                                                                 
Flags: X - disabled, R - running, S - slave 
 #    NAME                               MTU MAC-ADDRESS       ARP        MASTER-PORT                            SWITCH                           
 0    ether1-gateway                    1500 00:0C:42:E9:BA:8A enabled   
 1 R  ;;; To chiwa's router *** NO POE ***
      ether2-master-local               1500 00:0C:42:E9:BA:8B enabled    none                                   switch1                          
 2 RS ;;; to Vince' NS5M -  To Myrys
      ether3-slave-local                1500 00:0C:42:E9:BA:8C enabled    ether2-master-local                    switch1                          
 3 RS ;;; to NS5M east - To CDRX
      ether4-slave-local                1500 00:0C:42:E9:BA:8D enabled    ether2-master-local                    switch1                          
 4 RS ;;; to beaconing NS5M (port balcon.3)
      ether5-slave-local                1500 00:0C:42:E9:BA:8E enabled    ether2-master-local                    switch1

RouterOS v2
http://wiki.mikrotik.com/wiki/Manual:PoE-Out#RouterOS_2
http://wiki.mikrotik.com/wiki/Manual:PoE-Out#Changes_between_1.x_and_2.0_PoE-Out_controller_firmware

[admin@MikroTik] > interface ethernet poe monitor [find]
              name: ether2 ether3 ether4 ether5
   poe-out-voltage: 23.2V  23.2V  23.2V  
   poe-out-current: 224mA  116mA  64mA   
     poe-out-power: 5.1W   2.6W   1.4W

http://wiki.mikrotik.com/wiki/PoE-Out

/interface ethernet set ether2 poe-out=on
/interface ethernet set ether2 poe-out=off
/interface ethernet set ether2 poe-out=auto

Note:
<obinou> Le poe-out, il faut le mettre Ã "on" , et pas Ã "auto".
<obinou> sans Ã§a, j'ai l'impression que le RB fait un power-cycle si il dÃ©tecte une perte de link
<obinou> or, quand la NSM5 dÃ©marre, entre le bootloader & le firmware ca perd le link
<obinou> conclusion: reboot en boucle.

Note:
AprÃ¨s essais il est prÃ©fÃ©rable d'Ã©viter le 12V: Si au dÃ©part Ã§a semble marcher, les pics de courants
dÃ©passent parfois la limite autorisÃ© par port de 500mA, et le port se coupe immÃ©diatement.
Le 24V n'a pas montrÃ© ce souci.

Note 2:
Dans les derniers firmwares Microtik, l'option "poe-out" prend comme option "auto", "forced-on", ou "forced-off".

http://forum.mikrotik.com/viewtopic.php?f=3&t=49976&sid=40ea9661791968a896ab35214dc18f15&start=50
http://forum.mikrotik.com/viewtopic.php?f=3&t=57608

[admin@MikroTik-Ouin] > /interface ethernet print detail            
Flags: X - disabled, R - running, S - slave 
 0 R  name="ether1-gateway" mtu=1500 l2mtu=1600 mac-address=00:0C:42:D3:94:D5 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps 
 1    name="ether2-master-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D6 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 
 2    name="ether3-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D7 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 
 3 R  name="ether4-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D8 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on 
 4 R  name="ether5-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D9 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on

[admin@MikroTik-Ouin] > sys resource pr
                   uptime: 6m6s
                  version: 5.12
              free-memory: 17880KiB
             total-memory: 29708KiB
                      cpu: MIPS 24Kc V7.4
                cpu-count: 1
            cpu-frequency: 400MHz
                 cpu-load: 0%
           free-hdd-space: 30844KiB
          total-hdd-space: 61440KiB
  write-sect-since-reboot: 214
         write-sect-total: 96113
               bad-blocks: 0%
        architecture-name: mipsbe
               board-name: RB750UP
                 platform: MikroTik

NTP¶

/system ntp client set primary-ntp=172.31.31.254 enabled=yes

rsyslog¶

http://randomtweaks.blogspot.fr/2013/03/mikrotik-remote-logging-using-ubuntu.html

/system log action set 3 remote=172.31.31.252
/system log add action=remote disabled=no

Bridging sur le 750UP¶

Le RB750UP est conÃ§u dans l'idÃ©e d'en faire un CPE multi-antennes. Par dÃ©faut, le port 1 (POE-in ou LAN) n'est pas bridgÃ© sur le switch des 4 ports POE-out, on s'en sert plutÃ´t en mode routÃ©.

[admin@rb750up-chiwawa] > interface bridge add name=bridge1 
[admin@rb750up-chiwawa] > interface bridge port add bridge=bridge1 interface=ether1-gateway 
[admin@rb750up-chiwawa] > interface bridge port add bridge=bridge1 interface=ether2-master-local

DHCP sur le 750UP¶

Note: Attention, un serveur DHCP est actif par dÃ©faut sur les ports 2 Ã 5. Il faut le dÃ©sactiver
pour passer en mode switch.

ip dhcp-server print
ip dhcp-server remove 0

Routing sur le 750UP¶

ip route add dst-address=0.0.0.0/0 gateway=172.16.0.254

RB250GS¶

VLAN http://wiki.mikrotik.com/wiki/SwOS/Router-On-A-Stick
Doc http://wiki.mikrotik.com/wiki/SwOS
vlan limitation mikrotik rb250gs http://forum.mikrotik.com/viewtopic.php?f=17&t=45721
Routeur, switch, VLAN et multi-modems (via rb250gs) http://doc.rhizome-fai.net/doku.php?id=technique:routeur:vlan

RB750UP en mode BOX pour les nanostation¶

Connection to the routerboard

ssh admin@192.168.88.1

Reset the RouterBoard :

$Â setup 
$Â r
$ y

Le routerboard reboot et on se reconnect

Configuration du WAN

$ ip address add address=91.224.149.194/24 interface=ether1-gateway
$ ip route add gateway=91.224.149.254
$ ip address print 
$ ip route print

Fichiers

rb433l-conso-20131112.gnumeric (3,25 ko) rb433l-conso-20131112.gnumeric		Laurent GUERBY, 13/11/2013 09:40
conso-rb433l.png (16,5 ko) conso-rb433l.png		Laurent GUERBY, 13/11/2013 09:41

Projet

Général

Profil

Wiki

Observateurs (1)