{{>toc}}

h1. Mikrotik

RouterOS

http://wiki.mikrotik.com/wiki/MikroTik_RouterOS

http://wiki.mikrotik.com/wiki/Manual:TOC

http://wiki.mikrotik.com/wiki/Manual:Webfig

http://www.mikrotik.com/download.html

http://wiki.mikrotik.com/wiki/Upgrading_RouterOS

http://wiki.mikrotik.com/wiki/Supported_Hardware

http://wiki.mikrotik.com/wiki/Manual:Password_reset

http://wiki.mikrotik.com/wiki/Manual:PoE-Out

h2. Boitiers

* Nice box : http://forum.mikrotik.com/viewtopic.php?p=297825#p297825

* http://www.mikrotik.com/mfm

* http://www.aerial.net/shop/product_info.php?products_id=1085

* http://www.stationbox.info/

* Boîtiers Rexel très chers

* http://www.technic-achat.com/coffret-electrique-ip66-imo,fr,4,144T_XX.cfm (144T0010)

* http://www.interprojekt.com.pl/gold-alubox-outdoor-waterproof-case-p-472.html

* http://www.materielelectrique.com/coffret-polyester-marina-ip66-ik10-7035-300x220x160-p-6579.html

h2. Montage

* http://shop.varia-store.com/product_info.php?info=p1390_RF-Elements-EasyBracket---EasyBracket-Universal.html

h2. PoE

* http://www.i4wifi.eu/en/EU-230V-powering/PoE-convertor-48-V-24-V-802-3af-at.html

h2. Password

From: 	Le Net du Kermeur

Utilitaire mtpass, ça se trouve là : http://manio.skyboo.net/mikrotik/

Ca se compile sous g++, donc sur n'importe quel Linux ou *BSD.

Testé sous OpenBSD, il fait le boulot.

h2. RB433L and RB433UAHL

h3. NPK

http://routing.explode.gr/node/96

https://forum.openwrt.org/viewtopic.php?id=32320&p=3

https://forum.openwrt.org/viewtopic.php?pid=165526#p165526

https://github.com/lqez/npk

Easy install of OpenWrt on MikroTik's devices https://forum.openwrt.org/viewtopic.php?id=39171

http://wp.ayufan.eu/2013/02/the-rb951g-and-openwrt/

h3. Misc

TODO

http://i.mt.lv/routerboard/files/rb433L-series-qg_1377089307.pdf

http://forum.mikrotik.com/viewtopic.php?t=65977&p=336057

RF antenna and close miniPCI ?

h3. Power Consuption

<pre>

eth1 = PoE        192.168.88.101/24

eth2 = milieu     192.168.102.1/24

eth3 = oppose PoE 192.168.103.1/24

wlan1 = minipci du bas 172.31.31.43/24

http://dslrouter.sourceforge.net/stuff/mikrotik/mikrotik/AirMax5_and_Mikrotik_Router_Board_Connection_Guide_revised.pdf

netboot 

rb750up http://forum.mikrotik.com/viewtopic.php?f=3&t=57943&start=50

USB RB750UP http://patchwork.openwrt.org/patch/3252/

http://wiki.openwrt.org/toh/mikrotik/rb750

http://blog.poettner.de/2011/05/27/openwrt-trunk-on-mikrotik-routerboard-411750/

http://wiki.mikrotik.com/wiki/Manual:Netinstall

http://routerboard.com/pricelist/download_file.php?file_id=118

http://www.gowifi.co.nz/userguides/perform-a-netinstall.pdf

http://forum.mikrotik.com/viewtopic.php?f=2&t=66093

reset longer than 20 seconds

https://forum.openwrt.org/viewtopic.php?id=41490

RB433L

idle 108 mA 12V 

+1 eth 130mA 173 mA max au boot

RB433L + ethernet branché RouterOS 5.11

conso identique RouterOS 5.26

RouterOS 6.6 ?

Volt    mA  mW

(*  5.0 259)1295.0

(*  6.0 227)1362.0

(*  7.0 200)1400.0

(*  8.0 180)1440.0

(*  8.5 175)1487.5

(*  9.0 165)1485.0

(*  9.5 160)1520.0

(* 10.0 152)1520.0

(* 11.0 142)1562.0

(* 11.5 138)1587.0

(* 12.0 132)1584.0 152 pendant file upload  firmware (* 12.0 152)1824.0

(* 12.5 129)1612.5

(* 13.0 125)1625.0

(* 14.0 119)1666.0

(* 15.0 112)1680.0

(* 18.0  99)1782.0

(* 21.0  90)1890.0

(* 24.0  83)1992.0

(* 26.0  79)2054.0

(* 27.0  77)2079.0

RB433L sans ethernet

   V    mA  mW

4.0 off

(*  5.0 206)1030.0

(*  6.0 181)1086.0

(*  7.0 162)1134.0

(*  8.0 146)1168.0

(*  9.0 133)1197.0

(* 10.0 124)1240.0

(* 11.0 116)1276.0

(* 12.0 110)1320.0

(* 13.0 104)1352.0

(* 14.0  99)1386.0

(* 15.0  94)1410.0

diff ethernet pas ethernet constant en watt sur la plage de 265 mW a 260 mW

eth+ R52n-M  5180 AP-bridge 17dBm = 50 mW

(* 12.0 165)1980.0

vs (* 12.0 132)1584.0

0 dBm = 1 mW ou 7 dBm

conso inchangee

(* 12.0 163)1956.0

163-166

tout en bridge cote RB433L 7 dBm = 5 mW avec iperf 100M UDP

175-180

(* 12.0 (- 180 163))204.0 mW

serial http://forum.mikrotik.com/viewtopic.php?f=3&t=76194

http://wiki.openwrt.org/toh/mikrotik/rb433

http://wiki.mikrotik.com/wiki/Manual:Password_reset

http://wiki.mikrotik.com/wiki/MikroTik_Password_Recovery

http://wireless.kernel.org/en/users/Drivers/ath9k/devices

WLM200NX dual band

http://wireless.kernel.org/en/users/Drivers/ath5k

R52n-M

R52Hn

http://download2.mikrotik.com/routeros/5.26/routeros-mipsbe-5.26.npk

http://download2.mikrotik.com/routeros/6.6/routeros-mipsbe-6.6.npk

http://wiki.mikrotik.com/wiki/Netinstall

</pre>

!conso-rb433l.png!

h2. RB433 and RB433UAH and RB435G

h3. Links

http://routerboard.com/RB433

http://routerboard.com/RB433UAH

http://routerboard.com/RB435G

http://wiki.openwrt.org/toh/mikrotik/rb435

http://wiki.openwrt.org/toh/mikrotik/rb433

h3. Power Consumption

<pre>

RB433 MikroTik RouterOS 5.24

V    mA avec 1 eth

24.0 123 (* 24 0.123)2.952  (112 sans eth diff 0.264W)

16.0 149 (* 16 0.149)2.384

13.9 162 (* 13.9 0.162)2.2518  (142 sans eth diff 0.278W)

12.0 178 (* 12.0 0.178)2.136

10.0     207 (* 10.0 0.207)2.07

 8.0     250 (*  8.0 0.250)2.0

en dessous de 8 V : coupure

RB433UAH MikroTik RouterOS 5.24

avec 1 eth

24.0 189 (* 24 0.189)4.536

12.0 249 (* 12 0.249)2.988

 8.0 366 (* 8  0.327)2.616 292 sans eth

RB435G MikroTik RouterOS 5.24

avec 1 eth

24.0 117 (* 24.0 0.117)2.808 112 sans eth (* 0.005 24)0.12

12.0 187 (* 12.0 0.187)2.244

10.0 216 (* 10.0 0.216)2.16

 8.0 261 (*  8.0 0.261)2.088 255 sans eth (* 0.006 8.0)0.048

 7.0 303 (*  7.0 0.303)2.121

8.0

[admin@MikroTik] > system health print

     fan-mode: auto

      use-fan: main

   active-fan: none

      current: 172mA

  temperature: 20C

12.0

[admin@MikroTik] > system health print

           fan-mode: auto

            use-fan: main

         active-fan: none

            voltage: 11.3V

            current: 108mA => 192

        temperature: 20C

  power-consumption: 1.2W

24.0

[admin@MikroTik] > system health print

           fan-mode: auto

            use-fan: main

         active-fan: none

            voltage: 24V

            current: 50mA => 119

        temperature: 20C

  power-consumption: 1.2W

</pre>

h2. RB750UP

http://routerboard.com/RB750UP

http://blog.lekermeur.net/wp-content/uploads/2012/03/Printemps2012_RB750.pdf

Attention : problèmes lors que le RB750UP est alimenté en PoE : http://forum.mikrotik.com/viewtopic.php?f=3&t=57943

> we are working on new FW that would add useful features that are currently missing. One of them is reworked power management.

Voltage : http://forum.mikrotik.com/viewtopic.php?f=3&t=58124

> limit on power out port is 500mA regardless of output voltage. so at 12V you will be able to power only MAX 6W device. while at 30V 15W.

> If you power RB570UP with PoE 24V adapter over 100m cable, then resulting output voltage at full load (all 4 ports giving out 500mA totaling to 2A) then voltage to powered ports at RB750UP end will be around 21V then losses on cable and protections you end up with around 19V at the end device. and cables stretching for 200m from PSU brick.

> PoE in port has no input limitation only output is limited to 500mA and with 4 prots it is 2A

Upgrade to 5.20

<pre>

[admin@MikroTik] /interface ethernet poe settings> upgrade

Do you really want to upgrade PoE firmware? [y/n] 

y

Please reboot to finish PoE firmware upgrade.

[admin@MikroTik] /interface ethernet poe settings> pr

                   version: 2.0

  ether1-poe-in-long-cable: no

[admin@MikroTik] /interface ethernet poe> monitor [find]

               name: ether2-master-local ether3-slave-local ether4-slave-local ether5-slave-local

    poe-out-voltage:                                                           23.5V

    poe-out-current:                                                           160mA

      poe-out-power:                                                           3.7W

</pre>

* http://wiki.mikrotik.com/wiki/Manual:Upgrading_RouterOS

* To update firmware (latest RouterOS 5.12):

* Files / upload choose file : routeros-mipsbe-5.12.npk (12MB)

* Attendre la fin de upload

* System / Packages / IPv6 schedule for update

* System / Reboot

* about 90 seconds. Note: PoE will be cut during the reboot

chiwa admin VLAN 3175

192.168.3.20

telnet login admin pass (vide)

web

<pre>

[admin@rb750up-chiwawa] > interface ethernet print                                                                 

Flags: X - disabled, R - running, S - slave 

 #    NAME                               MTU MAC-ADDRESS       ARP        MASTER-PORT                            SWITCH                           

 0    ether1-gateway                    1500 00:0C:42:E9:BA:8A enabled   

 1 R  ;;; To chiwa's router *** NO POE ***

      ether2-master-local               1500 00:0C:42:E9:BA:8B enabled    none                                   switch1                          

 2 RS ;;; to Vince' NS5M -  To Myrys

      ether3-slave-local                1500 00:0C:42:E9:BA:8C enabled    ether2-master-local                    switch1                          

 3 RS ;;; to NS5M east - To CDRX

      ether4-slave-local                1500 00:0C:42:E9:BA:8D enabled    ether2-master-local                    switch1                          

 4 RS ;;; to beaconing NS5M (port balcon.3)

      ether5-slave-local                1500 00:0C:42:E9:BA:8E enabled    ether2-master-local                    switch1         

</pre>

RouterOS v2

http://wiki.mikrotik.com/wiki/Manual:PoE-Out#RouterOS_2   

http://wiki.mikrotik.com/wiki/Manual:PoE-Out#Changes_between_1.x_and_2.0_PoE-Out_controller_firmware

<pre>

[admin@MikroTik] > interface ethernet poe monitor [find]

              name: ether2 ether3 ether4 ether5

   poe-out-voltage: 23.2V  23.2V  23.2V  

   poe-out-current: 224mA  116mA  64mA   

     poe-out-power: 5.1W   2.6W   1.4W 

</pre>

http://wiki.mikrotik.com/wiki/PoE-Out

/interface ethernet set ether2 poe-out=on

/interface ethernet set ether2 poe-out=off

/interface ethernet set ether2 poe-out=auto

Note:

<obinou> Le poe-out, il faut le mettre à "on" , et pas à "auto".

<obinou> sans ça, j'ai l'impression que le RB fait un power-cycle si il détecte une perte de link

<obinou> or, quand la NSM5 démarre, entre le bootloader & le firmware ca perd le link

<obinou> conclusion: reboot en boucle.

Note:

Après essais il est préférable d'éviter le 12V: Si au départ ça semble marcher, les pics de courants

dépassent parfois la limite autorisé par port de 500mA, et le port se coupe immédiatement.

Le 24V n'a pas montré ce souci.

Note 2: 

Dans les derniers firmwares Microtik, l'option "poe-out" prend comme option "auto", "forced-on", ou "forced-off".

http://forum.mikrotik.com/viewtopic.php?f=3&t=49976&sid=40ea9661791968a896ab35214dc18f15&start=50

http://forum.mikrotik.com/viewtopic.php?f=3&t=57608

<pre>

[admin@MikroTik-Ouin] > /interface ethernet print detail            

Flags: X - disabled, R - running, S - slave 

 0 R  name="ether1-gateway" mtu=1500 l2mtu=1600 mac-address=00:0C:42:D3:94:D5 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps 

 1    name="ether2-master-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D6 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 

 2    name="ether3-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D7 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=auto 

 3 R  name="ether4-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D8 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on 

 4 R  name="ether5-slave-local" mtu=1500 l2mtu=1598 mac-address=00:0C:42:D3:94:D9 arp=enabled auto-negotiation=yes full-duplex=yes speed=100Mbps master-port=none bandwidth=unlimited/unlimited switch=switch1 poe-out=on 

</pre>

<pre>

[admin@MikroTik-Ouin] > sys resource pr

                   uptime: 6m6s

                  version: 5.12

              free-memory: 17880KiB

             total-memory: 29708KiB

                      cpu: MIPS 24Kc V7.4

                cpu-count: 1

            cpu-frequency: 400MHz

                 cpu-load: 0%

           free-hdd-space: 30844KiB

          total-hdd-space: 61440KiB

  write-sect-since-reboot: 214

         write-sect-total: 96113

               bad-blocks: 0%

        architecture-name: mipsbe

               board-name: RB750UP

                 platform: MikroTik

</pre>

h3. NTP

<pre>

/system ntp client set primary-ntp=172.31.31.254 enabled=yes

</pre>

h3. rsyslog

http://randomtweaks.blogspot.fr/2013/03/mikrotik-remote-logging-using-ubuntu.html

<pre>

/system log action set 3 remote=172.31.31.252

/system log add action=remote disabled=no

</pre>

h2. Bridging sur le 750UP

Le RB750UP est conçu dans l'idée d'en faire un CPE multi-antennes. Par défaut, le port 1 (POE-in ou LAN) n'est pas bridgé sur le switch des 4 ports POE-out, on s'en sert plutôt en mode routé.

Pour l'utiliser comme un simple switch et non comme un routeur il suffit de créer un bridge entre les interfaces :

<pre>

[admin@rb750up-chiwawa] > interface bridge add name=bridge1 

[admin@rb750up-chiwawa] > interface bridge port add bridge=bridge1 interface=ether1-gateway 

[admin@rb750up-chiwawa] > interface bridge port add bridge=bridge1 interface=ether2-master-local 

</pre>

h2. DHCP sur le 750UP

Note: Attention, un serveur DHCP est actif par défaut sur les ports 2 à 5. Il faut le désactiver

pour passer en mode switch.

<pre>

ip dhcp-server print

ip dhcp-server remove 0

</pre>

h2. Routing sur le 750UP

<pre>

ip route add dst-address=0.0.0.0/0 gateway=172.16.0.254

</pre>

h2. RB250GS

VLAN http://wiki.mikrotik.com/wiki/SwOS/Router-On-A-Stick

Doc http://wiki.mikrotik.com/wiki/SwOS

vlan limitation mikrotik rb250gs http://forum.mikrotik.com/viewtopic.php?f=17&t=45721

Routeur, switch, VLAN et multi-modems (via rb250gs) http://doc.rhizome-fai.net/doku.php?id=technique:routeur:vlan

h2. RB750UP en mode BOX pour les nanostation

Connection to the routerboard

<pre>

ssh admin@192.168.88.1

</pre>

Reset the RouterBoard :

<pre>

$ setup 

$ r

$ y

</pre>

Le routerboard reboot et on se reconnect

Configuration du WAN

<pre>

$ ip address add address=91.224.149.194/24 interface=ether1-gateway

$ ip route add gateway=91.224.149.254

$ ip address print 

$ ip route print 

</pre>